What is Audit Mode? Is a network-enabled environment where a user can add customizations to Windows images. Whenever Windows starts it shows you a Welcome screen immediately after installation, however one can skip this Welcome screen and boot directly to audit mode instead. Had a HP dv2915nr laptop hard drive died. Installed a new hard drive and use Recovery CD from HP. Installs for 4 hours and then stops: Windows could not complete installation. I called HP, they remoted in, and said the problem is in Windows because it will not install other printers. This is driving me crazy looking for a solution. Does anyone have any ideas? In short Audit Mode allows you to boot directly to Desktop after Windows installation. Windows could not complete the installation. To install Windows on this computer, restart the installation. Also, the main issue in this error is that you’re stuck in a Reboot loop and that’s why it’s more annoying. Now you know about Audit Mode and Welcome Mode it’s time how to fix this error, so without wasting any time let’s see how to Install Windows when in Audit Mode. • • • • • • Fix Windows Could Not Complete The Installation. To Install Windows On This Computer, Restart The Installation Method 1: Enable Administrator Account 1.On the error screen press Shift + F10 to open Command Prompt. 2.Type the following command and hit Enter: MMC 3.Next click File > Add/Remove Snap-in. 4.Select Computer Management and then double-click on it. 5.In the new window that open select Local computer and then click Finish followed by OK. 6.Then double-click Computer Management (Local) > System Tools > Local Users and Groups > Users > Administrator. 7.Make sure to Uncheck Account is disabled option and click OK. 8.Next, right click on Administrator then select Set Password and set a strong password to get started. 9.Finally, close everything and restart your PC. Sysprep Could Not Complete InstallationAfter the restart, you may be able to Fix Windows Could Not Complete The Installation. Method 2: Start Account Creation Wizard 1.Again open the Command Prompt on the error screen by pressing Shift + F10. 2.Type the following command and hit Enter: cd C: windows system32 oobe 3.Again type “ msoobe” (without quotes) and hit Enter. 4.The above will start user account creation wizard, so create a generic account and it’s password. Note: Keep your product key ready as sometimes it is required. If it asks for OEM/No then simply hit finish. 5.Once done hit Finish and close everything. Restart your PC you may have successfully Fix Windows Could Not Complete The Installation. To Install Windows On This Computer, Restart The Installation. Method 3: Change Password Requirements This error tends to pop-up when in Audit Mode and the computer has just been joined to a domain. The error is caused by password requirements added to the local security policy. This typically includes a minimum password length and password complexity. 1.Open the Command prompt on the error screen. 2.Type the following the command and hit Enter: secpol.msc 3.Navigate to Account Policies > Password Policy. 10 Windows Could Not Complete Installation4.Now change “ Minimum password length” to 0 and disable “ Password must meet complexity requirements.“ 5.Apply the changes and then exit the Security Policy console. 6.Click OK on the error message to reboot your PC. Method 4: Registry Fix 1.On the same error screen press Shift + F10 to open Command Prompt. 2.Type the following command and hit Enter: regedit 3.Now in the Registry Editor navigate to the following key: Computer HKEY_LOCAL_MACHINE SYSTEM Setup Status 4.Adjust the following values if they don’t match the following: Note: To change the value of the below keys double click on them and then enter the new value. HKEY_LOCAL_MACHINE SYSTEM Setup Status AuditBoot Value: 0 HKEY_LOCAL_MACHINE SYSTEM Setup Status ChildCompletion setup.exe Value: 3 HKEY_LOCAL_MACHINE SYSTEM Setup Status ChildCompletion audit.exe Value: 0 HKEY_LOCAL_MACHINE SYSTEM Setup Status SysprepStatus CleanupState Value: 2 HKEY_LOCAL_MACHINE SYSTEM Setup Status SysprepStatus GeneralizationState Value: 7 HKEY_LOCAL_MACHINE SYSTEM Setup Status UnattendPasses auditSystem Value: 0.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
November 2018
Categories |